Predator Bull bar to suit, Toyota Prado 250 Series 2025 to current

Offroad Animal Predator Bull Bar – Toyota Prado 250 Series (2025–Present)

The Prado 250 already has a lot happening across the front of the vehicle — parking sensors, radar, camera, headlight washers and factory fog lights — so a replacement bull bar needs to work around all of it properly.

The Offroad Animal Predator replaces the factory bumper without cutting the bumper or grille, while retaining the factory systems and giving you proper provision for a winch, recovery points and additional lighting.

It also sits around 140–150mm forward of the grille, keeping the front end relatively compact and giving the Prado useful clearance for off-road work.

Vehicle Fitment

Suits Toyota Prado 250 Series models from 2025 to Present, including:

• GX
• GXL
• VX
• Altitude
• Kakadu

The bar is ADR compliant and airbag compatible.

Factory Equipment Compatibility

The Predator is designed to work with the Prado's factory equipment, including:

• Parking sensors
• Adaptive cruise radar
• Headlight washers
• Factory fog lights
• Front camera

The supplied fitting components include dedicated sensor holders, radar mounting hardware, camera brackets and headlight-washer retainers to integrate these systems into the bar.

Weight & Front-End Fit

The complete bar weighs 65kg.

Around 23kg of factory components are removed during installation, giving a net increase of approximately 42kg over the standard front-end setup.

The bar sits approximately 140–150mm forward of the grille.

Winch Setup

The integrated winch cradle suits most low-mount winches up to 12,000lb, including the Warn Zeon.

The winch mounts feet-down and can be fitted after the bull bar is installed, which also makes later access and maintenance easier.

A number plate flip assembly is included for winch-equipped vehicles.

Recovery Points

Recovery points are built into the mounting system and supplied as standard with the bar.

That means the front protection, winch mounting and recovery setup are designed to work together rather than relying on separate add-on mounts later.

Lighting Options

The centre of the Predator can accommodate a 30–32" single-row LED light bar.

The factory fog lights are retained in the wings using the supplied mounting brackets.

Optional upper hoops are also available if you want additional protection or another lighting position.

Lighting and optional hoops are sold separately.

Steel Construction

The Predator is made mainly from 3mm and 5mm steel and uses a one-piece welded construction with welded wing supports.

The bar is zinc plated before being finished in matte black powder coat for corrosion protection.

Colour coding is also available.

Front Protection

A centre bash plate and under-wing panels are included as part of the setup, helping carry the protection underneath the front edge of the bar rather than leaving the lower section open.

What's Included

• 1 x bull bar weldment
• 1 x compliance plate
• 4 x sensor holders
• LH and RH headlight infills
• 1 x radar cover
• 850mm top-bulb pinch weld
• 1 x sensor tape kit
• LH and RH impact assemblies
• LH and RH recovery point assemblies
• 1 x centre mesh fairlead
• LH and RH fog-light brackets
• 1 x grille infill
• 1 x light-bar mesh infill
• LH and RH inner chassis support brackets
• LH and RH outer chassis support brackets
• 1 x radar mount
• Camera bracket housing
• Camera bracket
• 1 x grille support
• LH and RH headlight-washer retainers
• LH and RH headlight-infill mounts
• LH and RH wing-light mesh panels
• 1 x centre bash plate
• LH and RH wing underpanels
• 1 x number plate flip assembly
• Fitting hardware

For a Prado 250 being set up with a winch, recovery gear and extra lighting, the Predator gives you the mounting and protection you need while keeping the factory radar, camera, sensors, washers and fog lights integrated into the front of the vehicle.